Announce removal of all non-GPL or GPL-incompatible files
after August 2009.

Signed-off-by: Wolfgang Denk <wd@denx.de>

The mpc8313erdb board currently sets DBAT6 to cover all of the final 256MiB of
address space; however, not all of this space is covered by a device.  In
particular, flash sits at 0xfe000000-0xfe7fffff, and nothing is mapped
at the far end of the address space.

In zlib, there is a loop that references p[-1] if p is non-NULL.  Under
some circumstances, this leads to the CPU speculatively loading from
0xfffffff8 if p is NULL.  This leads to a machine check.

Signed-off-by: Scott Wood <scottwood@freescale.com>

continuation to the remaining mpc83xx boards that suffer from the same problem.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

commit 04e11cf3 "rtc: add support for 4543 RTC (manufactured by e.g.
EPSON)" introduces the following build error on boards configuring e.g,
the ds1374 rtc:

Configuring for MPC837XEMDS board...
ds1374.c:103: error: static declaration of 'rtc_read' follows non-static declaration
/home/r1aaha/git/u-boot/include/rtc.h:64: error: previous declaration of 'rtc_read' was here
ds1374.c:104: error: conflicting types for 'rtc_write'
/home/r1aaha/git/u-boot/include/rtc.h:65: error: previous declaration of 'rtc_write' was here

this reverts the erroneous chunk.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
CC: Detlev Zundel <dzu@denx.de>
CC: Andreas Pfefferle <ap@denx.de>

We had a bug on 86xx in which the boot page used to bring up secondary
cores was being overwritten and used for the malloc region in u-boot.

We need to reserve the region of memory that the boot page is going to
be put at so nothing uses it.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>

Match determine_mp_bootpg() that was added for 86xx.  We need this to
address a bug introduced in v2009.03 with 86xx MP booting.  We have to
make sure to reserve the region of memory used for the MP bootpg() so
other u-boot code doesn't use it.

Also added a comment about how cpu_reset() is dealing w/an errata on
early 85xx MP HW.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

* Use CONFIG_MP instead of CONFIG_NUM_CPUS to match 85xx
* Introduce determine_mp_bootpg() helper.  We'll need this to address a
  bug introduced in v2009.03 with 86xx MP booting.  We have to make sure
  to reserve the region of memory used for the MP bootpg() so other
  u-boot code doesn't use it.
* Added dummy versions of cpu_reset(), cpu_status() & cpu_release() to
  allow cmd_mp.c to build and work. In the future we should look at
  implementing all these functions. This could be common w/85xx if we
  use spin tables on 86xx.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

We're missing the board_lmb_reserve definitions that allow
cpu_mp_lmb_reserve to be called; this means that Linux
is free to reallocate reserved pages.  Linux currently boots
because we're getting lucky - the page we've reserved is
high enough in memory that it isn't allocated by Linux
while we still need it to be in existence.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Fix NAND support broken during new NAND code merge. Move those few lines of
code to board/netstar/netstar.c

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>

This patch fix the compiler/linker errors

common/cmd_i2c.c:1252: undefined reference to `i2c_get_bus_speed'
common/cmd_i2c.c:1256: undefined reference to `i2c_set_bus_speed'

if board use CONFIG_I2C_CMD_TREE and CONFIG_I2C_MULTI_BUS is not
uesd/undef (wrong define order)

and

removes additional empty lines

Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>

This patch adds MPC8569MDS board support. The UART, QE UEC1 and UEC2, BRD
EEPROM on I2C2 bus, PCI express and DDR3 SPD are supported in this patch.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

There is a workaround for MPC8569 CPU Errata, which needs to set Bit 13 of
LBCR in 4K bootpage. We setup a temp TLB for eLBC controller in bootpage,
then invalidate it after LBCR bit 13 is set.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

For the silicon which doesn't have ROM support in QE, it always needs to load
a pre-built ucode binary to IRAM so that QE can work.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com>

* Enable backside L2
* e500mc no longer has timebase enable in HID (moved to CCSR register)

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

- support mirrored DIMMs, not support register DIMMs
- test passed on P2020DS board with MT9JSF12872AY-1G1D1
- test passed on MPC8569MDS board with MT8JSF12864HY-1G1D1

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Travis Wheatley <travis.wheatley@freescale.com>

1. wr_lat
   UM said the total write latency for DDR2 is equal to
   WR_LAT + ADD_LAT, the write latency is CL + ADD_LAT - 1.
   so, the WR_LAT = CL - 1;
2. rd_to_pre
   we missed to add the ADD_LAT for DDR2 case.

Reported-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Dave Liu <daveliu@freescale.com>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The masks for various bit defines of LSDMR are common and thus we can
define them in one place rather than replicating them in each config.h

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>

Divisor field is called PTV not PVT.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Detlev Zundel <dzu@denx.de>

This patch adds the board specific communication routines needed by
the external 4543 RTC.

Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Andreas Pfefferle <ap@denx.de>

This patch adds advanced diagnosis functions for the inka4x0 board.

Signed-off-by: Andreas Pfefferle <ap@denx.de>
Signed-off-by: Detlev Zundel <dzu@denx.de>

Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Andreas Pfefferle <ap@denx.de>

This pretty unintelligent interface is used on some RTC chips.

Signed-off-by: Detlev Zundel <dzu@denx.de>

add CONFIG_CLPS7111_SERIAL to activate the driver

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

add CONFIG_LPC2292_SERIAL to activate the driver

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

add CONFIG_KS8695_SERIAL to activate the driver

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

add CONFIG_USB_S3C64XX to activate the driver

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>