All the DM-related configuration options are described in Kconfig
helps.  They should not be duplicated in README.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>

This strdup() is missing a check. Add it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>

enable generic board support for the ipam390 board.

Signed-off-by: Heiko Schocher <hs@denx.de>

- adapt to build with eldk-5.4
- add more targets for building with buildman:
  - freescale -x arm,m68k,aarch64
  - arm1136
  - arm1176
  - arm720t
  - arm920t
  - davinci
  - kirkwood

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Roger Meier <r.meier@siemens.com>

According to table 2-3 on page 87 of Marvell's latest PXA270
Specification Update Rev. I from 2010.04.19 [1] there exists a breed of
chips with a new CPU ID for PXA270M A1 stepping which our latest
Colibri PXA270 V2.4A modules actually have assembled. This patch helps
in correctly identifying those chips upon boot as well which then looks
as follows:

CPU: Marvell PXA27xM rev. A1

[1] http://www.marvell.com/application-processors/pxa-family/assets/pxa_27x_spec_update.pdf



Acked-by: Marek Vasut <marex@denx.de>

Fix the name appearing in menuconfig for memtest command

Signed-off-by: Nikolaos Pasaloukos <Nikolaos.Pasaloukos@imgtec.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com

Boards need to select CONFIG_SYS_GENERIC_BOARD in order to
prevent removal from the project.

Signed-off-by: Stefano Babic <sbabic@denx.de>

Boards need to select CONFIG_SYS_GENERIC_BOARD in order to
prevent removal from the project.

Signed-off-by: Stefano Babic <sbabic@denx.de>

Boards need to select CONFIG_SYS_GENERIC_BOARD in order to
prevent removal from the project.

Signed-off-by: Stefano Babic <sbabic@denx.de>

In 0200020b we added a number of tests for 'if
defined(CONFIG_SYS_FSL_SEC_LE) && !defined(CONFIG_MX6)' and
accidentally did one as 'ifdef defined...'

Signed-off-by: Tom Rini <trini@konsulko.com>

commit d9f43c8f sets
get_reset_cause() as static, but this conflicts with mx5
where its prototype is in sys_proto.h.

Drop it from sys_proto.h and drop print_cpuinfo from mx53_loco,
factorizing the call for this board.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <jason.hui@linaro.org>

Currently in some cases SDRAM init requires global_data to be available
and soon this will not be available prior to board_init_f().  Adjust the
code paths in these cases to be correct.  In some cases we had the SPL
stack be in DDR as we might have large stacks (due to Falcon Mode +
Environment).  In these cases switch to CONFIG_SPL_STACK_R.  In other
cases we had simply been setting CONFIG_SPL_STACK into SRAM.  In these
cases we no longer need to (CONFIG_SYS_INIT_SP_ADDR is used and is also
in SRAM) so drop those lines.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested on Beagleboard, Beagleboard xM
Tested-by: Matt Porter <mporter@konsulko.com>
Tested on Beaglebone Black, AM43xx GP EVM, OMAP5 uEVM, OMAP4 Pandaboard
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

When CONFIG_SYS_MALLOC_SIMPLE is defined, free() is a static inline. Make
sure that the export interface still builds in this case.

Signed-off-by: Simon Glass <sjg@chromium.org>

At present SPL uses a single stack, either CONFIG_SPL_STACK or
CONFIG_SYS_INIT_SP_ADDR. Since some SPL features (such as MMC and
environment) require a lot of stack, some boards set CONFIG_SPL_STACK to
point into SDRAM. They then set up SDRAM very early, before board_init_f(),
so that the larger stack can be used.

This is an abuse of lowlevel_init(). That function should only be used for
essential start-up code which cannot be delayed. An example of a valid use is
when only part of the SPL code is visible/executable, and the SoC must be set
up so that board_init_f() can be reached. It should not be used for SDRAM
init, console init, etc.

Add a CONFIG_SPL_STACK_R option, which allows the stack to be moved to a new
address before board_init_r() is called in SPL.

The expected SPL flow (for CONFIG_SPL_FRAMEWORK) is documented in the README.

Signed-off-by: Simon Glass <sjg@chromium.org>
For version 1:
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>

Signed-off-by: Tom Rini <trini@konsulko.com>

Use the full driver model GPIO and serial drivers in SPL now that these are
supported. Since device tree is not available they will use platform data.

Remove the special SPL GPIO function as it is no longer needed.

This is all in one commit to maintain bisectability.

Signed-off-by: Simon Glass <sjg@chromium.org>

This is already set up in crt0.S. We don't need a new structure and don't
really want one in the 'data' section of the image, since it will be empty
and crt0.S's changes will be ignored.

As an interim measure, remove it only if CONFIG_DM is not defined. This
allows us to press ahead with driver model in SPL and allow the stragglers
to catch up.

Signed-off-by: Simon Glass <sjg@chromium.org>

This function has grown into something of a monster. Some boards are setting
up a console and DRAM here in SPL. This requires global_data which should be
set up in one place (crt0.S).

There is no need for SPL to use s_init() for anything since board_init_f()
is called immediately afterwards.

Signed-off-by: Simon Glass <sjg@chromium.org>

This commit removes the dram reservation from board file,
because it is done in a common code.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This commit enables the last DRAM bank and reserves
the last 22 MiB of it, for the secure firmware.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Hyungwon Hwang <human.hwang@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Since more than one board requires memory reservation
for the secure firmware, the reservation code can be
made in a common code.
Now, to reserve some part of the the last bank,
board config should define:
- CONFIG_TZSW_RESERVED_DRAM - len in bytes
- CONFIG_NR_DRAM_BANKS - number of memory banks

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Hyungwon Hwang <human.hwang@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This patch suppress following warning:

board/samsung/common/board.c:95:32: warning: iteration 4u invokes undefined behavior [-Waggressive-loop-optimizations]
   addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
                                ^
board/samsung/common/board.c:94:2: note: containing loop

about possible signed integer overflow at gcc 4.8.2 (odroid board)

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Signed-off-by: Tom Rini <trini@konsulko.com>

Signed-off-by: Sinan Akman <sinan@writeme.com>

Add basic Xilinx ZynqMP arm64 support.
Serial and SD is supported.
It supports emulation platfrom ep108 and QEMU.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

This code was introduced to support the multiple .config
configuration in U-Boot.  We do not need it any more.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Fix trivial typo.

Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>

Signed-off-by: Tom Rini <trini@konsulko.com>

With a3895314 we now call readl() from this file so add <asm/io.h> so
that we have a prototype for the function.

Signed-off-by: Tom Rini <trini@konsulko.com>

Add EXT2/EXT4 and BOUNCE_BUFFER support.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>

With UMS support we are able to flash the eMMC from U-boot, which is very
convenient.

Add UMS support to make the eMMC flashing process easier.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>

Pass the same pad configuration as done in the kernel so that OTG1_ID pin can
properly work in device mode.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

After discussion during the last u-boot mini summit with USB maintainer -
Marek Vasut - it has been decided, that gadget development should be
coordinated by DFU custodian.

Such patch formalizes current development status.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>

Integrate latest validated register settings from Toradex WinCE BSP
4.2 working accross all module versions from early V1.x, V1.2D, V2.2B
to V2.4A.

Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>