Kconfig

	  This driver is enabled at runtime using the "ide0=dtc2278" kernel
	  boot parameter. It enables support for the secondary IDE interface
	  of the DTC-2278 card, and permits faster I/O speeds to be set as
	  well. See the <file:Documentation/ide.txt> and
	  <file:drivers/ide/legacy/dtc2278.c> files for more info.

config BLK_DEV_HT6560B
	tristate "Holtek HT6560B support"
	help
	  This driver is enabled at runtime using the "ide0=ht6560b" kernel
	  boot parameter. It enables support for the secondary IDE interface
	  of the Holtek card, and permits faster I/O speeds to be set as well.
	  See the <file:Documentation/ide.txt> and
	  <file:drivers/ide/legacy/ht6560b.c> files for more info.

config BLK_DEV_QD65XX
	tristate "QDI QD65xx support"
	help
	  This driver is enabled at runtime using the "ide0=qd65xx" kernel
	  boot parameter.  It permits faster I/O speeds to be set.  See the
	  <file:Documentation/ide.txt> and <file:drivers/ide/legacy/qd65xx.c> for
	  more info.

config BLK_DEV_UMC8672
	tristate "UMC-8672 support"
	help
	  This driver is enabled at runtime using the "ide0=umc8672" kernel
	  boot parameter. It enables support for the secondary IDE interface
	  of the UMC-8672, and permits faster I/O speeds to be set as well.
	  See the files <file:Documentation/ide.txt> and
	  <file:drivers/ide/legacy/umc8672.c> for more info.

endif

config BLK_DEV_IDEDMA
	def_bool BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA

config IDEDMA_IVB
	bool "IGNORE word93 Validation BITS"
	depends on BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS
	---help---
	  There are unclear terms in ATA-4 and ATA-5 standards how certain
	  hardware (an 80c ribbon) should be detected. Different interpretations
	  of the standards have been released in hardware. This causes problems:
	  for example, a host with Ultra Mode 4 (or higher) will not run
	  in that mode with an 80c ribbon.

	  If you are experiencing compatibility or performance problems, you
	  MAY try to answer Y here. However, it does not necessarily solve
	  any of your problems, it could even cause more of them.

	  It is normally safe to answer Y; however, the default is N.

config IDEDMA_AUTO
	def_bool IDEDMA_PCI_AUTO || IDEDMA_ICS_AUTO

endif

config BLK_DEV_HD_ONLY
	bool "Old hard disk (MFM/RLL/IDE) driver"
	depends on BLK_DEV_IDE=n
	help
	  There are two drivers for MFM/RLL/IDE hard disks. Most people use
	  the newer enhanced driver, but this old one is still around for two
	  reasons. Some older systems have strange timing problems and seem to
	  work only with the old driver (which itself does not work with some
	  newer systems). The other reason is that the old driver is smaller,
	  since it lacks the enhanced functionality of the new one. This makes
	  it a good choice for systems with very tight memory restrictions, or
	  for systems with only older MFM/RLL/ESDI drives. Choosing the old
	  driver can save 13 KB or so of kernel memory.

	  If you are unsure, then just choose the Enhanced IDE/MFM/RLL driver
	  instead of this one. For more detailed information, read the
	  Disk-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

config BLK_DEV_HD
	def_bool BLK_DEV_HD_IDE || BLK_DEV_HD_ONLY

endif

endmenu

endif